Product ID:D-DELTAMAX, CUT NICKEL IRON "C" & "E" CORES
MSDS Date:01/05/1987
FSC:9650
NIIN:00N030411
MSDS Number: BNNWN

ARNOLD ENGINEERING CO

300 WEST STREET
MARENGO, IL 60152
US

Emergency Phone: 815-568-2303

Info Phone: 815-568-2303

Preparer: K.L. LATIMER

Cage: 95566

ARNOLD ENGINEERING CO DIV OF SPS TECHNOLOGIES

G MARENGO, IL 60152 US

Telephone: 815-568-2000

Cage: 95566

NICKEL (SARA III)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 48%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3

IRON PEL/TLV AS IRON OXIDE

CAS: 7439-89-6

RTECS: NO4565500

Fraction By Weight: BALANCE

OSHA PEL 10 MG/M3

ACGIH TLV: 5 MG/M3

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:PRODUCT, AS SUPPLIED, PRESENTS NO
HEALTH HAZ. HAZARDOUS EXPOSURES COULD OCCUR ONLY BY PROCEDURES SUCH
AS ABRASIVE GRINDING, CUTTING OR MACHINING WITHOUT USE OF COOLANTS.
ANY LONG-TERM EXPOSURE TO DUST S EXCEEDING RECOMMENDED TLV LEVELS
MAY RESULT IN IRRITATION TO UPPER RESPIRATORY TRACT.DUSTS IN EYES
(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL: GROUP 2 (NTP), GROUP 1 (IARC).
Effects of Overexposure:HLTH HAZ: MAY CAUSE IRRITATION. PROLONGED SKIN
CONTACT WITH NICKEL MAY CAUSE ALLERGIC REACTION IN SENSITIVE
INDIVIDUALS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:EYES:FLUSH WITH WATER FOR AT LEAST 15 MINUTES. INGEST:CALL MD
IMMEDIATELY . INHAL:REMOVE TO FRESH AIR. SUPPORT BREATHING (GIVE
O2/ARTIFICIAL RESPIRATION) . SKIN:FLUSH WITH COPIOUS AMOUNTS OF
WATER. CALL MD .

Flash Point:NON COMBUSTIBLE
Autoignition Temp:Autoignition Temp Text:]
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE .
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:FINE METAL POWDERS MAY CAUSE EXPLO
HAZ.PROD IS NOT COMBUST. IF ADDITIONAL GRINDING/MACHINING IS
PERFORMED,IT SHOULD BE DONE USING COOLANTS TO CONTROL DUST LEVS.

Spill Release Procedures:DUSTS MAY BE SWEPT WET OR VACUUMED TO KEEP
AIRBORNE DUST CONCENTRATIONS TO A MINIMUM.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:USE GOOD MANUFACTURING PRACTICES AND
GOOD HOUSEKEEPING PRACTICES THAT WILL KEEP GENERATED DUSTS TO A
MINIMUM.
Other Precautions:USE PERSONAL PROTECTION EQUIPMENT WHEN REQUIRED.
AVOID INGESTION OF DUSTS BY NOT EATING, DRINKING OR SMOKING IN
AREAS WHERE DUSTS OR FUMES ARE GENERATED.

Respiratory Protection:IF AIRBORNE CONCENTRATIONS EXCEED THOSE
SPECIFIED, NIOSH/MSHA APPROVED RESPIRATOR SHOULD BE USED.
Ventilation:GRINDING/MACHINING OPERATIONS SHOULD BE PERFORMED USING
COOLANTS TO REDUCE DUSTS. ADEQ LOC VENT SHOULD BE USED (SUPDAT)
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:USE GOOD PERSONAL HYGIENE PRACTICES.
Supplemental Safety and Health
VENT:WHEN DRY GRINDING OR MACHINING ALLOYS TO KEEP EXPOSURE LEVELS
BELOW RECOMMENDED TLV.

HCC:N1
Spec Gravity:8.25
Solubility in Water:NOT SOLUBLE
Appearance and Odor:SILVER GRAY WITH NO ODOR.

Stability Indicator/Materials to Avoid:YES
POWDERS/DUSTS FROM PRODUCT ARE INCOMPATABLE WITH STRONG OXIDIZING
AGENTS SUCH AS NITRIC ACID.
Stability Condition to Avoid:GENERATION OF AIRBORNE DUSTS.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.